This an easy modification that only requires minimal wiring.  Origin and several pictures of the modification credit to Spannerhead ( ...

This is your basic fuel setup for an aftermarket fuel pressure regulator. This guide assumes you will be using AN ...

This How to was Archived from Mx6.com King6fab did not design or originate this how to. It has been copied ...

What is the HEI modification? You may  have heard of it on forums and groups of Facebook. If your new, ...

This How-To will guide through a complete transmission tear down and rebuild using a 1995 Ford Probe GT G-Series transmission, ...

Below is the turbo timer wiring Diagram, refer to your specific turbo timer instructions for installation ...

...

A Hydraulic Lash Adjuster or better known as an HLA is nothing more than an ordinary hydraulic lifter. It (on ...

This is guide is for modifying your KLDE fuel rails and installing Nissan Injectors along with how to shave them ...

Oil Temp - Suitable location for Oil Temp gauge and/or Oil Pressure Gauge Located to the right of the clutch ...

...

This is guide is for reference only. All information used from this guide is for free distribution. User assumes all ...

...

Diyautotune IGN-6 Coil Pack This coil pack can only be found from Diyautotune.com, its expensive compared to other options and ...

Rear Brake-Callipers - Design fault on pre 5th Jan 95 versions, self-destruct Work-around - Short-lived, fix is rebuilt/new (Sumitomo redesigned) ...

Technical Data Ignition Area: Spark-plug gap: 1.0-1.1mm on 2.0 & 2.5 Spark plugs - 2.5: NGK ZFR5F-11 (standard), NGK ZFR6F-11 ...

Site Objective This website aims to provide a knowledge base for 2nd generation Mazda MX6 & 626, Ford Probe and ...

Bad grounds can result in no start issues and faulty sensor readings.  Check ground connections for clean metal contact and ...

Information:  Fact: The 1993-1994 (KL) V6 Engine ECU use 2 crank sensors, one crank sensor at the crank pulley, and ...

* 2nd Gen clutch line is same as 1st gen, interchangable * Clutch line is also interchangable with 1994 Ford ...

SEAT BELTS All seat belt anchors = 29-57 ft. lbs. Seat belt retractors = 29-57 ft. lbs. STARTER 28-38 ft ...

Angel Eye Halo High & Low Beam  H7 ASPECS High & Low Beam 9004 JSPECS High Beam H3C JSPECS Low ...

...

...

Step 1. Testing for Power (Figure 1) Here we are testing for 12 volt power to the distributor. This is ...

1993-1995 v6 KLDE CEL Codes The OBD-1 computer system was used in the 93-95 Ford Probe, Mx6 & 626 To ...

OBD-2 codes for the 1996+ KLDE V6 MX6, 626 and Ford Probe These codes must be read from the car ...

Installation of the King6fab J-Spec brackets is very simple.  Below is a drawing of the brackets showing the positions of ...

Below are downloadable diagrams that demonstrate the proper wiring connection for your application ...

Installation How to 1.Locate the fuel rail electrical connectors, It is recommended to do one at a time. 2.Start with ...

This installation is rather straight forward, King6fab put this guide together to aid in common issues that come up when ...

This guide assumes you have already gone through the process of removing your OEM Timing belt tensioner.      Start by fully ...

Manual Download Link File Size MSPNP Coil Pack Wiring Harness Install Guide PDF 725 KB Polyurethane Shifter Assembly Bushing Kit ...

Pictures are in Ultra High Resolution, Please select your year and download diagram. 1993-1994 HEI 1993-1994 HEI with Coil 1995-1997 ...

Wheel chock the front tires. Jack up the rear of the car via the center of the sub-frame. Place jack ...

King6fab's Unique and one off design for the utilization of traction bars was developed with ease of installation in mind.  ...

This how to describes the process of removing the OEM bushings and installing the Polyurethane bushings.  The standard procedure for ...

Do not route these harness’s over hot objects such as exhaust manifolds or piping Begin your install at Step 10 ...

DIY Polyurethane Control Arm Bushing Installation Jack car up and place support jack stands. Remove both left and right wheels ...